Author |
Topic: Program Pricing (Read 419 times) |
|
Pete
Full Member
member is offline
 
Posts: 167
|
 |
Program Pricing
« Thread started on: Dec 4th, 2012, 5:02pm » |
|
How exactly does it work in cabinet planner?
|
|
 Logged
|
|
|
|
Rob
Administrator
member is offline
Gender: 
Posts: 882
|
|
Re: Program Pricing
« Reply #1 on: Dec 4th, 2012, 5:24pm » |
|
Not very well. 
From the in-program help file:
Once you have established your base prices, press the button with "$$" on it and the program will compute a price for each cabinet according to the height, width and depth. These prices are based on your standard setting for each cabinet type. For instance, your standard upper cabinet height is 30, your standard depth is 12 and your base price is $40 per foot. If you plan a 12w x 30h x 12d upper, the price will be $40. If you increase any of the sizes by 23% the price will also increase by 23%. With a little experimenting you will have your job pricing done with the click of one button.
|
|
Logged
|
Please remember this forum is for users to help each other. If you need a faster answer to a question email me directly.
|
|
|
Pete
Full Member
member is offline
Posts: 167
|
|
Re: Program Pricing
« Reply #2 on: Dec 6th, 2012, 05:43am » |
|
Its not consistent is there any way to base it on a linear foot price
|
|
Logged
|
|
|
|
Rob
Administrator
member is offline
Gender:
Posts: 882
|
|
Re: Program Pricing
« Reply #3 on: Dec 6th, 2012, 08:08am » |
|
Do you mean so that the price per foot says the same regardless of the cabinet's height or depth?
|
|
Logged
|
Please remember this forum is for users to help each other. If you need a faster answer to a question email me directly.
|
|
|
Pete
Full Member
member is offline
Posts: 167
|
|
Re: Program Pricing
« Reply #4 on: Dec 6th, 2012, 2:03pm » |
|
Yes, sort of.
Most base cabinets will be 21" 24" deep and uppers 12" so it would be easier if it was a linear foot with adjustments to the other sizes ... yes?
The LF cost could be marked up per material/door etc cherry vs. maple and flat panel vs. mitered applied molding.
How does it currently work for drawer units and if you custom build a cabinet not using a base or upper, but rather a tall custom with pull outs and doors along with DF's then the current is not close ... right?
Link in this post http://cabplanner.conforums.com/index.cgi?board=wish&action=display&num=1354665806 because you are basing the vanity which is a base with the drawers swapped with Doors, but using the tall custom pricing
|
| « Last Edit: Dec 6th, 2012, 2:08pm by Pete » |
Logged
|
|
|
|
Rob
Administrator
member is offline
Gender:
Posts: 882
|
|
Re: Program Pricing
« Reply #5 on: Dec 6th, 2012, 3:33pm » |
|
If you adjust your Tall Custom price it should work. On my setup I have the Tall cabinet standard height set to 84" and the Base standard height of 34.5". Dividing 84 by 34.5 comes out to ~2.43, so I set the Base price to $100 per foot and the Tall Custom to $243(2.43 times the Base price) per foot. Comes out pretty close.
@ 34.5" high
Unit # 1 - 24.00" Base 200.00
Unit # 4 - 24.00" Tall Custom 199.61
@ 84" high
Unit # 2 - 24.00" Tall Custom 486.00
|
|
Logged
|
Please remember this forum is for users to help each other. If you need a faster answer to a question email me directly.
|
|
|
|
