Author |
Topic: Glitch (Read 207 times) |
|
NickB
Junior Member
member is offline
Gender: 
Posts: 95
|
 |
Glitch
« Thread started on: Feb 24th, 2011, 4:53pm » |
|
I downloaded the latest update last night to play with the 3d rendering stuff.
I was in adjusting cabinets and the measurment that tells you where you are in the lower left hand corner is all jumbled and you cannot make out the numbers.
Nick
|
|
 Logged
|
|
|
|
trulycustom
Junior Member
member is offline
Gender:
Posts: 93
|
|
Re: Glitch
« Reply #1 on: Feb 24th, 2011, 5:53pm » |
|
Nick, Now that you mention it mine is the same. I did't say anything because I figured it was my machine.
kent
|
|
Logged
|
|
|
|
NickB
Junior Member
member is offline
Gender:
Posts: 95
|
|
Re: Glitch
« Reply #2 on: Feb 24th, 2011, 6:30pm » |
|
Kent glad it wasn't just me too!
I also noticed that the mesurments along the top of the drawing are hidden unless you zoom out but then you can't drag another cabinet in unless you input its location.....
It would be nice for all the measurements to be visable and also to have them included going vertical.
Nick
|
|
Logged
|
|
|
|
Pete
Full Member
member is offline
Posts: 167
|
|
Re: Glitch
« Reply #3 on: Feb 24th, 2011, 8:09pm » |
|
make that 3 too
|
|
Logged
|
|
|
|
Rob
Administrator
member is offline
Gender:
Posts: 882
|
|
Re: Glitch
« Reply #4 on: Feb 25th, 2011, 08:29am » |
|
Try it now. I moved the "loc" down to the status bar and reduced the initial elevation scale a little bit.
If anyone still has trouble with it send me a screen shot along with your monitor's screen resolution and DPI settings.
|
|
Logged
|
Please remember this forum is for users to help each other. If you need a faster answer to a question email me directly.
|
|
|
trulycustom
Junior Member
member is offline
Gender:
Posts: 93
|
|
Re: Glitch
« Reply #5 on: Feb 25th, 2011, 09:43am » |
|
Rob, That fixed it for me!!! Thanks.
Kent
|
|
Logged
|
|
|
|
NickB
Junior Member
member is offline
Gender:
Posts: 95
|
|
Re: Glitch
« Reply #6 on: Feb 25th, 2011, 9:48pm » |
|
Rob wasn't there a numeric scale (lower left hand side)that changed as you drag the mouse across the screen that tells you where you are in relation to the 0 start point of the wall?
All the numbers are clear now to see thank you! And also the length of the cabinet there when you drag it out.
Thanks,
Nick
|
| « Last Edit: Feb 25th, 2011, 9:49pm by NickB » |
Logged
|
|
|
|
Rob
Administrator
member is offline
Gender:
Posts: 882
|
|
Re: Glitch
« Reply #7 on: Feb 26th, 2011, 06:00am » |
|
Right, that's what I moved down to the status bar.
|
|
Logged
|
Please remember this forum is for users to help each other. If you need a faster answer to a question email me directly.
|
|
|
NickB
Junior Member
member is offline
Gender:
Posts: 95
|
|
Re: Glitch
« Reply #8 on: Feb 26th, 2011, 10:07am » |
|
Ahhhhh yes you did!!
Thanks Rob guess I should have read your post better!! 
I was so accustom to it being in the other spot that I didn't notice it way down there!!
Thanks again!
Nick
|
|
Logged
|
|
|
|
Rob
Administrator
member is offline
Gender:
Posts: 882
|
|
Re: Glitch
« Reply #9 on: Feb 26th, 2011, 10:36am » |
|
   
|
|
Logged
|
Please remember this forum is for users to help each other. If you need a faster answer to a question email me directly.
|
|
|
|
